3000R Multi-Temp
Multi-Temp for your Multi-Stop Operation.
VIEW OUR STOCK INVENTORY!
Utility 3000R Multi-Temp
Built with the same industry-leading technologies of the 3000R, the Utility 3000R Multi-Temp reefer is customizable with a variety of options to meet your unique operational requirements.
Multi-Temp load partition system
CenterSeal® load partition device
Key Features
- Foam-in-place insulation
- Versitex®-Utility VR2 lining
- Integrated heavy-duty 10" high wearband
- 100% LED lighting
- Support leg bracing
- Corrosion protection
- Impact-absorbing rear gusset
- ConMet Preset Plus® premium wheel end system
- Unique tensioned roof design
- 5⁄16" thick dock board guide plates" data-note="Dock board guide plates protect the rear of the trailer floor from dock plate damage.">5⁄16" thick dock board guide plates
- Thermal barriers
- Ultra Road Shield™ Plus (URS+)
- 100% soldered main harness
Available Options
- CenterSeal® load partition device
- Air return bulkheads
- Recessed logistic track
- Clearance light packages
- Electrical system options
- Severe service high impact linings
- Factory-installed rear & side door lift gates
- Temperature management systems
- Custom positioned side doors
- Remote magnetic shut-off switches
- Remote evaporators
- Roll up door installation
- Stainless steel I.C.C. bumper
- Stainless steel wingplates
- Custom wearbands
- Stainless steel electropolished lock rods
- Front corner protectors
- Severe service kingpin section
- Exterior rub rails
- Customized floor systems
- Factory-installed refrigeration units and accessories
- Electric stand-by refrigeration units
- Factory-installed decals
- Tri-fold rear doors
- Walk ramps from major suppliers
- Multi-Temp load partition system
- Multiple strip curtain configurations
- Retractable platforms and stairs
- Anti-dock walk devices and dump valves
- Shore power plug at rear
- Tire inflation systems
- Grab handles
- Side and rear steps
- Verta-Lock® vertical shoring system
- LED dome lights
Specifications
| 01-03 DIMENSIONS AND DECK TYPE | |
|---|---|
| Gross vehicle weight rating (GVWR) | |
| 65,000 lb | |
| Payload capacity | |
| 55,000 lb | |
| Inside height | |
| 104⅛" | |
| Inside width | |
| 97½" at wearband | |
| Overall length | |
| 53' 0" | |
| Overall height | |
| 13' 6" on 46½" height 5th wheel | |
| Overall width | |
| 102⅜" | |
| Deck type | |
| Straight | |
| 04 FRONT SUBFRAME | |
| Front subframe | |
| 4¼" deep box beam design | |
| Approach plate | |
| 9 ga. high strength steel full width | |
| Kingpin location | |
| 36" from front | |
| Kingpin plate | |
| 3 ga. high strength steel full width | |
| Kingpin type | |
| AAR hardness cruciform | |
| Cover plate | |
| Extruded aluminum on front face of approach plate | |
| 05 SUPPORT LEG AND ASSEMBLY | |
| Support legs | |
| Jost® model A401 enhanced 50,000 lb capacity | |
| Support leg location | |
| 105" from center line of kingpin to center line of support legs | |
| Support leg shoe type | |
| 10" × 10" ultra low profile cushion foot | |
| Support leg bracing | |
| Bolt-on cross-bracing with 7 ga. 3¼" deep high strength steel channels | |
| Support leg crank location | |
| Roadside of support legs | |
| 06 CROSSMEMBERS AND RAILS | |
| Bottom rails | |
| 11" deep heavy-duty extruded aluminum; tapered front and rear | |
| Crossmembers front subframe to legs | |
| 4" aluminum I-beam crossmembers with 4 rivet end clips on 12" center line | |
| Crossmembers legs to rear subframe | |
| 5½" aluminum I-beam crossmembers with 4 rivet end clips on 12" center line | |
| Crossmembers over rear subframe | |
| 4" steel I-beam crossmembers with 4 rivet end clips on 12" center line with standard reinforcement of an additional crossmember in rear 34" | |
| Crossmembers over support legs | |
| (5) 4" steel I-beam crossmembers with 4 rivet end clips on 12" center line over legs | |
| 07 REAR SUBFRAME | |
| Rubber dock bumpers | |
| 1 pair | |
| Vertical and horizontal I.C.C. bumper | |
| D.O.T. high strength steel vertical with non-slip 7" deep horizontal | |
| 08 SUSPENSION, AXLES AND ACTUATION | |
|---|---|
| Hendrickson air ride system with integral axles | |
| Hendrickson® ULTRAA-K air ride/slider system with 49" axle spacing | |
| Slider suspension location | |
| 70" rear and 166" forward for 96" of slider travel | |
| Slider pin release mechanism | |
| Hendrickson® Quik-Draw® air-operated slider repositioning system | |
| Slack adjusters | |
| Bendix® Versajust® automatic | |
| Air actuation system | |
| 1 tank with spring brakes | |
| Air brake chambers | |
| Bendix® EnduraSure™ 3030 | |
| Air ride dump valve | |
| Hendrickson® automatic | |
| Anti-lock brake system (ABS) | |
| Bendix® TABS-8 2S/1M with TRSP | |
| Axle spindle nuts | |
| ConMet® included with Preset Plus® | |
| Brake lining style | |
| Hendrickson® HXS brake lining style | |
| Hub piloted system with outboard drums | |
| 10 stud hub-piloted system with outboard cast drums with 16½" × 7" brakes included with ConMet Preset Plus® | |
| Hubcaps | |
| Federal-Mogul “non-vented” | |
| Oil seals | |
| ConMet® included with Preset Plus® | |
| Wheel bearing lubrication | |
| Mobilube HD Plus 80W-90 oil | |
| Wheel bearings | |
| ConMet® included with Preset Plus® | |
| 09 FRONT WALL | |
| Front panels | |
| .040" aluminum, pre-painted white with Ultra Road Shield™ Plus (URS+) | |
| Front wall posts | |
| 1" J-shaped extruded aluminum post with 2 additional 3¼' deep steel reefer unit support posts | |
| Front corner post | |
| .080" extruded aluminum 4¾" radius | |
| Front corner post inserts | |
| Stainless steel | |
| Front top rail | |
| Extruded aluminum wraparound | |
| Gladhands and receptacle location | |
| Gladhands and receptacle mounted on an aluminum extrusion offset to roadside | |
| Prep for front mount refrigeration unit | |
| Without electric standby | |
| Refrigeration unit opening cover | |
| Sheet metal cover includes sealant full perimeter of opening | |
| 10 SIDE WALL | |
| Side panels | |
| .040" aluminum flat side panels, pre-painted white with Ultra Road Shield™ Plus (URS+) | |
| Side posts | |
| 1" J-shape extruded aluminum posts with 16" maximum center line from front to rear of support legs with 24" center line legs to rear; 2 additional posts each side over front subframe | |
| 11 ROOF | |
| Roof skin | |
| .025" one-piece aluminum coil | |
| Roof bows | |
| 1" extruded aluminum J-shaped bows on 48" center lines | |
| Top rails | |
| 6⅜" heavy-duty extruded aluminum | |
| 12 REAR CASE AND DOORS | |
| Rear case & buckplate material | |
| Stainless steel for satin finish swing doors | |
| Rear case corner posts & header | |
| Stainless steel for satin finish swing doors | |
| Rear door hinge material | |
| Non-polished aluminum | |
| Rear door hinges | |
| 4 per door | |
| Holdbacks | |
| Chain link and hook type door | |
| Rear door lock rods | |
| 1 per door | |
| Rear door panels | |
| .040" aluminum exterior panel | |
| Rear door type | |
| Utility-Design Barrier Door® | |
| 14 FLOORS | |
|---|---|
| Floor type | |
| 1½" extruded aluminum high wear 20K duct floor system and integral 10" heavy-duty extruded aluminum non-tapered wearband | |
| Fork lift reinforcing | |
| Bearing grid system at rear with full width hardwood fillers and aluminum I-cores rear 36" of floor in center 68"; 1 additional crossmember at rear for maximum 6" center line at rear 34" | |
| Troughs | |
| Extruded aluminum front and rear | |
| Drains | |
| 2 drains front and rear | |
| 15 INSULATION | |
| Side wall thickness | |
| 2" | |
| Front wall thickness | |
| 4" | |
| Crossmember floor fillers | |
| Full length hardwood | |
| Floor thickness | |
| 3" | |
| Floor underskin | |
| .040" Versitex® | |
| Rear door thickness | |
| 3" | |
| Roof thickness | |
| 3" | |
| 16 LINING | |
| Front wall lining | |
| .065" Versitex®-Utility VR2U | |
| Side wall lining | |
| .065" Versitex®-Utility VR2U | |
| Wearband | |
| 10" high 3⁄16" thick heavy-duty extruded aluminum non-tapered integral with floor | |
| Rear door lining | |
| .065" Versitex®-Utility VR2U | |
| Roof lining | |
| .065" Versitex®-Utility VR2U | |
| 17 ELECTRICAL | |
| Electrical receptacle | |
| 7-way without circuit breakers | |
| Main harness | |
| Utility moisture-resistant 6-wire harness with internal ground and 7-way plug | |
| Clearance lights quantity | |
| 0-1-2-5 D.O.T. minimum clearance light package | |
| Rear header clearance lights | |
| Grote® Micronova® LED grommet-mounted | |
| Upper clearance lights | |
| Factory choice LED with 3" mounting hole at center line | |
| Lower clearance lights | |
| Grote® Micronova® LED PC-rated | |
| Side mounted directional light | |
| Grote® Supernova® LED combo on bracket below bottom rail (each side) | |
| ABS warning light | |
| Grote® Micronova® LED PC-rated | |
| Stop, tail, turn lights | |
| Grote® 4" LED (10-diode) lights, 2 per side with black snap-in flange | |
| Conspicuity tape location | |
| On bottom rails and at rear | |
| 18 PAINT AND FINISH | |
| Front panel finish | |
| Pre-painted white with Ultra Road Shield™ Plus (URS+) | |
| Front corner post finish | |
| Natural aluminum | |
| Front corner post insert finish | |
| Stainless steel | |
| Front subframe assembly finish | |
| Fully immersed in black rust preventative coating (zero VOC hot dip) | |
| Side panel finish | |
| Pre-painted white with Ultra Road Shield™ Plus (URS+) | |
| Rear case finish | |
| Satin finish stainless steel | |
| Rear subframe finish | |
| Black scharpf | |
| Vertical & horizontal I.C.C. bumper finish | |
| Utility black enamel on horizontal bumper, black scharpf on vertical bumper | |
| Bottom side rail finish | |
| Natural aluminum | |
| Top front & top side rail finish | |
| Natural aluminum | |
| Roof exterior finish | |
| Natural aluminum | |
| Support leg finish | |
| Rust preventative coating | |
| 19 MISCELLANEOUS | |
|---|---|
| Mudflap type | |
| Black plastic anti-sail with Utility logo, mounted with steel reinforcing straps | |
| 20 TIRES AND WHEELS | |
| 22.5" × 8.25" standard width wheels | |
| Factory choice steel 10 hub piloted wheels | |
| Tires | |
| 295/75R 22.5” Michelin X®-Line Energy-T2 14ply Load Range 'G' | |